Differences

This shows you the differences between two versions of the page.

--- cli:franke:hwinstallation [2023/07/28 16:55]
p.russo
+++ cli:franke:hwinstallation [2023/08/01 17:01] (current)
p.russo
@@ Line 20: / Line 20: @@
 {{:cli:franke:touch-barcode.jpg?1024| how to wire a touch panel}}\\ \\
 {{:cli:franke:touch-panel.jpg?1024| The barcode reader}}\\ \\ \\ \\
 The Mini PC is connected to the LED TV via an HDMI port and is also connected to the system via an ethernet cable.\\ \\
@@ Line 28: / Line 29: @@
 Each PLC can be connected to 4 machines as it is provided with 8 slots.\\ \\
 {{:cli:franke:plc.jpg| The PLC}}\\ \\ \\ \\
+Follow the procedure below for the correct connection of the devices:
+{{ :cli:franke:f1.png?800 |}} \\ \\
+{{ :cli:franke:f2.png?800 |}} \\ \\
+{{ :cli:franke:f3.png?800 |}} \\ \\
+{{ :cli:franke:f4.png?800 |}} \\ \\
+{{ :cli:franke:f5.png?800 |}} \\ \\
+{{ :cli:franke:f6.png?800 |}} \\ \\
+{{ :cli:franke:f7.png?800 |}} \\ \\
+{{ :cli:franke:f8.png?800 |}} \\ \\
+{{ :cli:franke:f9.png?800 |}} \\ \\
+{{ :cli:franke:f10.png?800 |}} \\ \\
+{{ :cli:franke:f11.png?800 |}} \\ \\
+{{ :cli:franke:f12.png?800 |}} \\ \\
+{{ :cli:franke:f13.png?800 |}} \\ \\
+{{ :cli:franke:f14.png?800 |}} \\ \\
+{{ :cli:franke:f15.png?800 |}} \\ \\
+Instructions for TV setup: \\ \\
+{{ :cli:franke:f16.png?800 |}} \\ \\
+{{ :cli:franke:f17.png?800 |}} \\ \\
+{{ :cli:franke:f18.png?800 |}} \\ \\
+{{ :cli:franke:f19.png?800 |}} \\ \\
+{{ :cli:franke:f20.png?800 |}} \\ \\
+{{ :cli:franke:f21.png?800 |}} \\ \\
+{{ :cli:franke:f22.png?800 |}} \\ \\
+{{ :cli:franke:f23.png?800 |}} \\ \\
+{{ :cli:franke:f24.png?800 |}} \\ \\
 ===== Interfaces =====
@@ Line 124: / Line 154: @@
 **With a PLC**\\
-The main difference compared to a line without a PLC concerns the signaling mode of the advancement of a piece: it is the PLC that automatically sends a signal as soon as the operator performs the last operation.\\ \\
+The main difference compared to a line without a PLC concerns the signaling mode of the advancement of a piece: it's up to PLC to automatically send a signal as soon as the operator performs the last operation.\\ \\
 {{:cli:franke:worker2.png?900| Advancement of the pieces with the PLC}}\\ \\ \\ \\
@@ Line 219: / Line 249: @@
 When the resource has a stop machine running, two additional buttons will be shown.\\ \\
 {{:cli:franke:screen2.png?1024| stop machine running }}\\ \\ \\ \\
-The operator will press the green one with the wrench icon and then will confirm the choise.\\
+The operator will press the green one with the wrench icon and then will confirm the choice.\\
-Success / error message will be shown based on the result of the operation.\\
+Success / error message will be shown depending on the result of the operation.\\
-Now, the green button become grayout (disabled) and the other button with the wrench icon become red: the operator has to press it to end the maintenance.\\
+Now, the green button become grayout (disabled) and the other button with the wrench icon becomes red: the operator has to press to end the maintenance.\\
-The running stop machine remains as is until the operator press the yellow blinking button “failure / slowdowns”.\\ \\
+The running stop machine remains as it is until the operator press the yellow blinking button “failure / slowdowns”.\\ \\